Install the flange as shown in the illustration. After checking to be sure that no belt teeth in the section marked with A are lifted up and that the teeth in each sprocket are engaged, secure the tensioner pulley. Screw the special tool until it contacts the timing belt tensioner arm. Remove the timing belt under cover rubber plug and then install special tool MD998738. Turn the crankshaft in the proper rotation direction (clockwise) for two rotations, and recheck to be sure that the timing marks on each sprocket are aligned.ģ. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke. Be sure not to turn the crankshaft in the opposite direction (counter clockwise).Ģ. Initially loosen the fixing bolt of the tensioner pulley fixed to the engine mount side by 1/4 - 1/2 turn, and use the force of the tensioner spring to apply tension to the belt.ĬAUTION: As the purpose of this procedure is to apply the proper amount of tension to the tension side of the timing belt by using the cam driving torque, turn the crankshaft only by the amount given below. Install the timing belt in the following order, while making sure that the tension side of the belt is not loose.ġ. Align each of the camshaft and crankshaft sprocket timing marks.ģ. Hello i have a 2003 lancer es 2.0 timing belt broke bent valves replaced all bent valves and head all timing on point but will not start checked all points fuel relays make vlicking noise relay one has two powers on right side and relay 2 has 1 top right pin getting power also the fuses are all good in engine bay and under dash also getting power to red wire on fuel pump when cranking sends. Then temporarily tighten tensioner bolt.Ģ. With the timing belt tensioner pulley bolt loosened, use a screwdriver to pry the tensioner pulley as close to the engine mount as possible. Recheck to be sure that the belt is fully tensioned and that each timing mark is in the proper position.ġ. When should Mitsubishi oz rally lancer timing belt be replaced 60000 miles. Temporarily tighten the tensioner pulley bolt.ĬAUTION: After installing the timing belt, try to rotate the camshaft sprocket in the reverse direction. How do you replace the timing belt on a 2003 Mitsubishi Lancer. Place a screwdriver against the tensioner pulley and pry it fully back in the direction of the arrow.Ĥ. Loosen the tension pulley fixing bolt.ĬAUTION: If the timing belt is to be re-used, use chalk to mark (on its flat side) an arrow indicating the clockwise direction.ģ. Turn the crankshaft clockwise (right turn) to align each timing mark and to set the number 1 cylinder at compression top dead center.Ģ. All attached pictures correlate with these directions.ĬAUTION: The crankshaft should always be turned only clockwise.ġ. His high quality car buying tutorials offer help to the car buying public.Here are the directions for timing belt replacement specific to your vehicle. He is a professional car buyer and consumer advocate working closely in the industry to improve the buyer’s experience. Greg Macke is a car blogger and author of “My 7 Secrets to Buying a High Quality Used Car”. The 16 Valve Volvo engines are all Interference 3.0L Inline 6 VVT-i (1998 2JZ-GE) InterferenceĢ.0L – 8 valve Non-Interference (However there have been instances of bent valves)ī5XXX five-cylinder inline engines -Interference.3.0L Inline 6 (Except 1998 2JZ-GE) Non-Interference.1.6L DOHC (4A-GE & 4A-GZE) Non-Interference.1.6L DOHC (4A-F & 4A-FE) Non-Interference. 2.0L DOHC (626, MX-6 & Protege) Non- Interference.After 2005 both, the 2.3-liter 4-cylinder and the 3.0-liter V6 engines have a maintenance-free timing chain. All Honda engines are interference except 3.0L & 3.2 which are Non-interference The 4-cylinder 2.0-liter 16-valves DOHC 127-hp Ford Zetec engine used a timing belt that needs replacement at 120k.1.6L SOHC 16 Valve Engine (Tracker) Interference.1.6L SOHC 8 Valve Engine (Tracker) Non-Interference.1.6L DOHC (1989-92 Prizm GSI) Non-Interference.1.6L (Chevette & 1000) Non-Interference.2.0L SOHC Gasoline (Capri, Pinto & Ranger) Non-Interference.2.0L SOHC Gasoline (Escort, Focus & Tracer) Non-Interference.2.0L DOHC (Contour, Escape, Focus, Mystique, ZX2 & 1999-2002 Cougar) Non-Interference.3.0L SOHC 12 Valve Engine Non-Interference.2.4L DOHC Non-Interference (Valves may hit if camshafts turn out of time).2.8L V6 90 100 Quattro A4 A6 Interference.The video below will also help you determine if your car has a timing belt or chain. An interference engine is one that has insufficient clearance between the valves and pistons if the cam stops turning due to a broken timing belt. The result is usually catastrophic engine failure. The following list will provide you the information on whether your car engine is an interference engine or a non-interference engine.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |